Myth Buster

Well Pump Short Cycling? The “Bad Pressure Switch” Myth

Short cycling is usually a waterlogged pressure tank, not a bad pressure switch. A 15-minute test to tell them apart, the right precharge, and when adding air is unsafe.

UsuallyA waterlogged tank, a failed bladder or a precharge set wrong
SometimesA clogged switch sensing nipple, burned contacts, a clogged filter near the tank, or a leak
Get rightWatch the gauge, test the precharge with the tank drained and the pump off, and never add air to a tank that has been losing it

This guide contains affiliate links. As an Amazon Associate we earn from qualifying purchases, at no extra cost to you. Read our full affiliate disclosure.

Where the “Bad Pressure Switch” Myth Comes From

The pump clicks on, runs a few seconds, clicks off, and repeats. The pressure switch is the part you can see clicking, so it gets the blame. It is also cheap and easy to swap, so many homeowners replace one first and find the problem is still there.

The switch only reacts to pressure. It turns the pump on at the cut-in pressure (commonly 30 or 40 psi) and off at the cut-out (commonly 50 or 60 psi). What decides how long the pump runs between those two points is the pressure tank. Amtrol calls the water delivered between pump cycles the tank’s drawdown: the bigger the drawdown, the less often the pump has to start. When a tank loses its air cushion, drawdown drops to almost nothing and the pump hits cut-out within seconds.

Myth vs. Fact

MythFact
“Short cycling means a bad pressure switch.”Usually not. The most common cause is a waterlogged tank or a failed bladder. Check the tank before replacing the switch.
“Just add air to the tank.”Can be unsafe. Amtrol warns not to add pressure to an in-service tank that has lost air or whose cycle time has dropped; it can signal internal corrosion and a risk of rupture.
“Set the tank to any pressure that works.”False. Precharge should be 2 psi below cut-in, measured with the tank drained and the pump off: 38 psi for a 40/60 switch.
“Short cycling is just annoying.”False. Every start heats the motor and wears the switch contacts, capacitor and relays. Frequent starts shorten pump system life.
“A bigger tank fixes all cycling.”Only sometimes. A leak, a running toilet, a faulty check valve or a clogged sensing nipple will still cycle the pump.
“Good water pressure means the tank is fine.”False. Pressure can look normal at the tap while the pump starts every few seconds. Watch the gauge, not the shower.

Why Short Cycling Matters

A submersible or jet pump motor heats up every time it starts and needs run time to shed that heat. Franklin Electric’s submersible motor installation manual treats the average number of starts per day as a major factor in system life, and excessive cycling wears out pressure switches, starters, relays and capacitors. Providing a minimum run time per start is one of the jobs Amtrol lists for a correctly sized and charged pressure tank.

The cost of ignoring it: a burned-out switch or capacitor is a nuisance; a failed submersible motor means pulling the pump. See well water pump repair and replacement costs.

Step 1: Read the Pressure Gauge (2 Minutes)

Open one faucet and watch the gauge at the pressure tank through a few cycles:

What the gauge doesWhat it usually means
Swings between cut-in and cut-out in a few seconds, with a short pump run each timeWaterlogged tank or low precharge. Go to the tank test.
Pump clicks on and off rapidly at about the same pressure (chattering near cut-in)Switch problem: a clogged sensing nipple, burned contacts or a loose switch. Go to the switch check.
Pump turns on when no water is being usedLeak or check valve: a running toilet, a leaking fixture or pipe, or a check valve letting water drain back.
Pressure never reaches cut-out, or rises very slowlyNot short cycling: a pump, well yield or clogged filter problem.

Quick tap test: knock on the side of the tank from top to bottom. On a healthy bladder tank the top section sounds hollow (air) and the bottom sounds dull (water). A tank that sounds dull and solid all the way up is probably waterlogged.

Step 2: Test the Tank Precharge (15 Minutes)

  1. Turn off power to the pump at the breaker.
  2. Drain the system: open a faucet, ideally the one nearest the tank or the tank’s own drain, until the water stops and the gauge reads zero.
  3. Measure the air charge at the valve on top of the tank with a tire pressure gauge.
  4. Compare it with your switch’s cut-in pressure. The precharge should be 2 psi below cut-in: 28 psi for a 30/50 switch, 38 psi for a 40/60 switch.
  • Precharge correct (within a couple of psi): the tank is probably fine, so move on to the switch.
  • Water or wet air comes out of the air valve: the bladder has failed. Replace the tank.
  • Precharge low or zero on a tank that has been in service: the tank has lost air. Amtrol’s manual says not to adjust or add pressure to a tank that has lost air or whose pump cycle time has dropped, because that can mean internal corrosion and a risk of rupture. Replace the tank.
  • Precharge simply set wrong after a switch change, with no air loss: adjust it to 2 psi below the new cut-in, with the tank drained and the pump off, following the tank manufacturer’s instructions.

Older plain steel tanks without a bladder are a different design: they waterlog by nature and are drained and re-aired periodically, often with an air volume control. Follow that tank’s instructions, or consider replacing it with a bladder tank.

Safety: pressure tanks store energy. If the tank is visibly corroded, leaking, or you are not sure what type it is, call a licensed well contractor.

Tank or Switch? Check Your Numbers

Pick what your gauge does and enter what you measured. Add your tank size and pump flow to see how long a healthy tank should keep the pump running, and compare it with the run you timed.

Interactive check

Tank or Switch? Check Your Short Cycling

Pick what the gauge does and enter what you know. The check compares your precharge with the 2 psi rule, estimates how long a healthy tank should keep the pump running, and tells you what to fix first.

What does the pressure gauge do?

Cut-in and cut-out are usually on the pressure switch cover or in its manual: 30/50 and 40/60 are the most common. Tank size is on the label, and the GPM calculator finds your pump flow.

Step 3: Check the Pressure Switch

Only after the tank checks out. Turn off power first: the switch has exposed live terminals under the cover.

  1. Inspect the contacts. Burned or heavily pitted contacts are a common switch failure and often first show up as erratic cycling. Replace the contacts, or the switch, if they are badly pitted.
  2. Clean the sensing nipple and port. The small pipe fitting under the switch can clog with sediment, iron or scale, especially with galvanized fittings. A clogged nipple makes the switch react to pressure surges instead of the real system pressure, which causes rapid on and off cycling. Remove the switch, clear the nipple and port, and reinstall it.
  3. Check the settings. A typical residential differential is 20 psi (30/50 or 40/60). Amtrol warns that a narrow differential with an undersized tank can make the pump cycle rapidly and damage it.
  4. Replace the switch if the contacts are burned, the diaphragm is damaged or it will not hold its settings, and always match the tank precharge to the new cut-in.

If the switch ever fails to shut off, pressure can climb dangerously high. Make sure your system has a working pressure relief valve.

Step 0: Confirm Your Numbers

Know your settings before you touch anything. Cut-in and cut-out are usually marked on the pressure switch or in its manual, and the tank size is on its label. If iron or sediment keep clogging the switch nipple, a quick strip test tells you how much iron your well carries. Our guide explains how to test well water step by step.

Other Causes of a Pump That Keeps Turning On and Off

  • A clogged filter near the tank or switch. A plugged sediment or iron filter between the pump and the pressure switch can make pressure spike at the switch and cycle the pump rapidly. Change it, and see the best sediment filters for well water.
  • Leaks and running fixtures. A running toilet, dripping outdoor faucet, leaking irrigation line or underground pipe makes the pump start with no one using water.
  • A failing check valve. If water drains back down the well, pressure drops and the pump restarts. A slow pressure drop with every fixture closed is the clue.
  • A softener or filter regenerating. Backwashing filters and softeners draw water for a while and can cycle the pump overnight. That is normal if it is brief; a softener that never stops filling is not. See water softener full of water?

For how these parts connect, see the residential well water system diagram.

What It Costs to Fix

Typical ranges; local rates vary:

FixDIY partsWith a well contractor
Clean the sensing nipple, adjust settings$0$100 to $200 service call
New pressure switch$25 to $60$150 to $300
New bladder pressure tank$200 to $600 (20 to 40 gallon class)$500 to $1,500 installed
Check valve replacement$20 to $60 (above ground)$300 to $1,500 or more if the pump must be pulled
Motor or pump replacement after years of cyclingNot a DIY job$1,000 to $3,000 or more

Plan the upkeep with the annual well water system maintenance cost estimator and the well water maintenance checklist.

The Bottom Line

A pump that clicks on and off every few seconds is usually telling you the pressure tank has lost its air cushion, not that the switch is bad. Read the gauge, test the precharge with the tank drained and the pump off, and replace a tank with a failed bladder or one that keeps losing air instead of pumping it back up. Only then move to the switch: clean the sensing nipple, inspect the contacts and match the settings to the tank. Fixing it quickly protects the most expensive part of the system, the pump motor.

  1. Watch the gauge through a few cycles to see which pattern you have.
  2. Test the precharge: pump off, system drained, 2 psi below cut-in.
  3. Fix in order: the tank first, then the switch sensing nipple and contacts, then leaks and the check valve.

Frequently Asked Questions

What causes a well pump to short cycle?

Most often a waterlogged pressure tank, a failed bladder or a precharge set wrong. Other causes include a clogged pressure switch sensing nipple, burned switch contacts, a clogged filter near the tank, leaks and a faulty check valve.

How do I know if my pressure tank is waterlogged?

The pump runs only a few seconds per cycle and the gauge swings quickly between cut-in and cut-out. Knocking on the tank sounds dull all the way up. With the pump off and the system drained, the air valve reads low or zero, or spits water.

What should the air pressure be in my well pressure tank?

2 psi below the pressure switch cut-in setting, measured with the pump off and the tank drained of water: 28 psi for a 30/50 switch or 38 psi for a 40/60 switch.

Can I just add air to a waterlogged pressure tank?

Not if it is a bladder tank that has lost air while in service. Amtrol’s manual warns not to add pressure to a tank that has lost air or whose cycle time has dropped, because it can mean internal corrosion and a risk of rupture. Replace it, and only adjust precharge on a tank that has not lost air, such as after changing the switch setting.

What are the symptoms of a bad pressure switch?

Rapid clicking at about the same pressure, a pump that will not start or will not shut off, burned or pitted contacts and settings that drift. A clogged sensing nipple under the switch causes similar symptoms and only needs cleaning.

Is short cycling bad for a well pump?

Yes. Each start heats the motor and wears the switch contacts, capacitor and relays, so frequent starts shorten the life of the whole pump system.

How long should a well pump run each cycle?

Long enough to avoid rapid starts, which a correctly sized and charged tank is designed to provide. If your pump runs only a few seconds per cycle, the tank is waterlogged, undersized or the precharge is wrong.

Why does my well pump turn on when no water is being used?

Usually a leak, such as a running toilet, dripping faucet or underground pipe, or a check valve letting water drain back into the well. Close every fixture and watch the gauge: a steady drop points to a leak or the check valve.

Sources and How We Researched This

This guide was compiled by the WellWaterAdvisor editorial team from pressure tank and pump manufacturer documentation and pressure switch service guidance. Drawdown and run time in the check above are calculated with Boyle’s law from your switch settings and tank size. Turn off power to the pump before opening the pressure switch cover, and call a licensed well contractor for corroded or leaking tanks, buried wellheads or any work that requires pulling the pump.

Related tools: well GPM calculator, maintenance cost estimator, well water diagnostic calculator.

More Myth Busters

Myth BusterWill a Bigger Well Pump Increase Water Pressure? The GPM vs. PSI MythA bigger pump moves more gallons per minute but does not raise pressure: the pressure switch sets psi. Why oversized pumps short cycle, and the checks to run first.Read the guide Myth BusterDoes Reverse Osmosis Waste Too Much Water? The “4 Gallons Down the Drain” MythTypical RO sends 4 to 9 gallons to the drain per gallon; WaterSense systems send 2.3 or less. Real ratios, why wells do worse, septic, reuse and a waste calculator.Read the guide Myth BusterWater Softener Full of Water? The “Broken Softener” MythWater in the brine tank is usually normal; water above the salt is not. The normal level, the brine-draw test, and how to fix a clogged injector, salt bridge or mushing.Read the guide Myth BusterIs Softened Water Safe to Drink? The “Dangerously Salty” MythA softener adds about 8 mg/L of sodium per grain of hardness. How much is in your glass, who should not drink softened water, and when potassium chloride or RO makes sense.Read the guide Myth BusterDoes UV Light Work on Well Water? The “UV Fixes Everything” MythA UV light kills bacteria in well water, but only in clear water. The hard limits for iron, hardness, manganese and turbidity, the right install order and how to size it.Read the guide Myth BusterDoes Shocking a Well Fix It for Good? The Shock Chlorination MythShocking a well kills bacteria today, but it rarely fixes odors or contamination for good. How to dose it right, protect your septic system and know when the water is safe.Read the guide Myth BusterDoes Boiling Well Water Purify It? (Why It Makes Heavy Metals Worse)Boiling kills germs, but it removes no chemicals and concentrates nitrate, lead and arsenic. When to boil well water, and what to use instead.Read the guide Myth BusterDo Salt-Free Water Softeners Work? What They Fix and What They Don’tThey can cut limescale, but they do not soften water. What the research shows, and when a salt-free system is the wrong buy for a well.Read the guide Myth BusterDoes a Water Softener Remove Iron? What Works and What FailsA softener can take out some iron, but only one kind and only in small amounts. Here is where the line is, and what to install instead.Read the guide